Renogy 3000W 12V Pure Sine Wave Inverter Renogy 3000W 12V Pure Sine Wave Inverter
SKU: RNG-INVT-3000-12V-P2-G3-US
- Continuous output 3000W
- One-second surge 6000W
- Battery system 12V DC
P2 Series Pure Sine Wave
Renogy 3000W 12V Pure Sine Wave Inverter — Inverter Only
The 3000W P2 inverter converts 12V battery power to 115V AC (120V-class US output) at 60Hz. Renogy rates this model for 3000W continuous output and 6000W peak power for one second. This listing is the inverter-only package; battery cables and batteries are not included.
Renogy 3000W P2: match the load, battery and connections
The Renogy 3000W 12V pure sine wave inverter supplies 3000W continuously, with 6000W surge for one second. Add the appliances that run together and check motor or compressor startup duration separately. The wattage is shared across every AC output.
Check battery current before choosing capacity
At a 12V battery voltage and an assumed 85% conversion efficiency, a 3000W AC load draws approximately 295A DC (3000 ÷ 12 ÷ 0.85). This is a planning calculation, not a fixed current specification or a fuse recommendation. Voltage sag, startup loads and cable losses can increase demand. Check the battery BMS, terminals, conductors and protection together.
A single battery limited to 200A continuous discharge cannot support the full 3000W output at 12V: even before inverter losses, the load requires 250A. More amp-hours do not automatically mean a higher discharge-current limit.
AC output and control
Three AC sockets and an AC terminal block; a 5V/2.1A USB port; and a wired remote are provided. The A2 manual limits each receptacle to 15A. The combined inverter wattage is not available from one receptacle. This P2 has no battery charger, solar charging input, Bluetooth module support or automatic AC transfer function.
US output: the linked A2 manual specifies 115V AC at 60Hz; Renogy’s retail table describes it as 120V. This is not a 230V/240V-output model. Use the supplied unit label and manual when checking equipment and installation limits.
What’s included
- 1 × 3000W 12V P2 inverter
- 1 × wired remote control
- 1 × 5 m (16.4 ft) RJ11 remote-control cable
- 1 × user manual
Battery cables are not included with the 3000W model. The battery bank, battery-side fuse/disconnect and any separate charging or transfer equipment are not part of this inverter-only package. Included cable sizes describe the box contents; longer runs require installation-specific sizing.
Plan the installation
Use our RV inverter sizing guide to check running watts, startup demand and battery discharge limits before choosing wiring and protection.
For battery selection, compare Renogy batteries by capacity, discharge limit and cold-weather features. Battery voltage and discharge limits must match the planned load; this is not a blanket compatibility claim.
What the 3000W inverter does
Run suitable AC loads from a correctly sized 12V battery system. This inverter supplies three AC sockets, one AC terminal block and a 5V/2.1A USB port. Check each appliance’s running and startup wattage before connecting it.
Pure sine wave AC output
Pure sine wave output is intended for compatible electronics and appliances that require AC power. The inverter does not charge a battery or directly accept a solar panel input.
3000W running power, 6000W peak
The 3000W continuous rating applies to the combined running load. Renogy lists 6000W peak power for one second for startup demand; check the specific appliance’s startup requirements as well as the battery’s discharge capability.
Match the load to the AC output
Renogy specifies 115V AC (120V-class US output) at 60Hz. Confirm the appliance voltage, frequency and wattage before use.
Plan the 12V battery supply
Full 3000W output places substantial demand on a 12V battery bank. Confirm that the battery BMS, terminals, fuse and wiring can support the inverter under the installation instructions.
Account for startup surges
Motors and compressors can require more power at startup than while running. Compare their startup requirement with the inverter’s peak rating and the battery system’s limits.
Cooling Fan Design
Keep the inverter’s fan and ventilation openings clear, and follow Renogy’s mounting and clearance instructions.
Output and installation safety
Use the provided wired remote and follow Renogy’s manual for output wiring, grounding, fusing and safe operation.
Ground the chassis as instructed
Connect the chassis ground according to Renogy’s installation instructions and applicable electrical requirements.
Build the battery side correctly
Renogy does not include battery cables with the inverter-only package. Select cables, terminals and overcurrent protection for the current and cable run specified by the installation instructions.
Power for a properly sized mobile system
The 12V inverter can serve suitable RV and off-grid AC loads when the battery bank, wiring and ventilation are designed for the load.
What comes in the inverter-only box
Renogy lists one 3000W inverter, one wired remote control, one 5 m RJ11 cable and one user manual. Batteries and battery cables are separate purchases.
Inverter use in a mobile power system
For mobile installations, plan the battery bank and cable route around the expected AC load before mounting the inverter.
Check the full system before installation
Check appliance startup demand, 12V battery discharge current, cable size and grounding as one system.
Use in a suitable off-grid system
The inverter provides 115V AC (120V-class US output) from a correctly installed 12V battery system; follow the manufacturer’s installation and environmental limits for the intended location.
Size the inverter
Our RV inverter sizing guide explains continuous watts, startup loads and battery-side demand before choosing an RV inverter.
| Renogy 3000W P2 US inverter | |
| Selected variant SKU | RNG-INVT-3000-12V-P2-G3-US |
|---|---|
| Verified specifications | |
| Continuous Output Power | 3000W |
| Peak Power Rating | 6000W for 1 second |
| Output Voltage | 115V AC per A2 manual; 120V-class US retail description |
| Output Frequency | 60Hz |
| AC Output Sockets | 3 |
| AC Terminal Block | 1 |
| USB Power Port | 5V / 2.1A |
| Power Output Control | ON / OFF / REM switch and included wired remote |
| Output Waveform | Pure sine wave |
| Nominal Efficiency | >90% |
| Total Harmonic Distortion (THD) | <3% per A2 manual |
| Nominal Input Battery Voltage | 12V DC |
| Battery Terminal Size | M8 × 1.25 × 15 mm |
| Low Battery Alarm | 11V ± 0.3V DC (A2 manual) |
| Battery Low Shutdown | 10.5V ± 0.3V DC (A2 manual) |
| Over Voltage Shutdown | 16.5V ± 0.3V DC (A2 manual) |
| No Load Current Draw | <2.5A |
| Dimensions | 18.9 × 9.0 × 4.0 in / 480 × 229 × 102 mm |
| Weight | 12.5 lb (A2 manual) |
| Cooling Fan | Thermally controlled |
| Operating Temperature Range | -4°F to 104°F / -20°C to 40°C |
| Inverter Remote Control | 5 m / 16.4 ft wired RJ11 cable |
| Material and Workmanship Warranty | 1 Year |
| Storage Temperature | -40°F to 158°F / -40°C to 70°C |
| Battery Input Voltage Range | 10V to 16V DC |
| Full Load Efficiency | >85% per A2 manual |
| Humidity | Maximum 93%, non-condensing |
| Safety Standards | ETL listed to UL 458 and CSA C22.2 No. 107.1 per manual introduction |
| Cable | Battery cables not included |
| Battery Charging | Not built in |
| Solar Input | No direct solar charging input |
| AC Transfer Switch | Not built in |
| Bluetooth | Not supported |
| Specification Source | Linked Renogy P2 A2 US manual; retail revision values may differ |
| Individual AC Receptacle Limit | 15A per A2 manual; all outputs share total inverter rating |
Frequently Asked Questions
Clear answers to common questions about this product, setup, compatibility, and use.


