Renogy Wanderer Li 30A PWM Solar Charge Controller — 12V Renogy Wanderer Li 30A PWM Solar Charge Controller — 12V
SKU: RNG-CTRL-WND30-Li-G1-US
- Charge current 30A
- Battery system 12V only
- Enclosure IP20
Wanderer Li 30A solar charging: choose by the system
The Wanderer Li 30A is a negative-ground PWM solar charge controller for a 12V battery bank. It supports sealed AGM, gel, flooded and compatible lithium charging profiles, with LED status indicators and optional BT-1 monitoring. Its 30A rating does not make it a 24V controller.

30A charging for a 12V bank
This model has solar and battery connections, a temperature-sensor input and an RS232 monitoring port. It does not have the Wanderer 10A’s DC load terminals, timed load modes, USB ports or LCD. Power loads from the correctly protected battery circuit, using a separately sized inverter where AC power is required.
Match the solar array and battery
Solar input limit: 25 V DC maximum Array guidance: Select by 30 A charge-current and 25 V PV-voltage limits; no universal array configuration is implied. Check panel open-circuit voltage at the lowest design temperature and array current before choosing series or parallel connections. PWM charging requires a panel configuration appropriate to the battery voltage; the controller does not offer MPPT voltage conversion.
Set the battery chemistry and charging parameters to the battery manufacturer’s requirements. This model is designed for a 12V battery bank; it does not auto-select a 24V system. Lithium defaults are intended for a 12.8V LFP bank; parameter changes use the supported monitoring interface. Temperature compensation and lead-acid equalization must not be treated as universal lithium settings. Battery/BMS cold-charge restrictions still apply.
What’s included
- 1 × Renogy Wanderer Li 30A PWM Charge Controller
BT-1 and the remote temperature sensor are optional. The manual says wall-mounting screws are not supplied. Solar panels, batteries, site wiring and circuit protection are selected separately.
Display and optional monitoring
LED status indicators and battery-type button; no LCD. RS232; optional Renogy BT-1 Bluetooth module, sold separately. LED indicators show charging/battery status; an optional module adds phone monitoring.

Compare the right controller
Choose the Wanderer 10A when a smaller 12V/24V array, LCD, USB output or timed DC loads are more useful than 30A charging. Choose Adventurer Li 30A for a flush-mounted LCD and 12V/24V support; its electrical limits and mounting needs differ.
Compare Renogy Wanderer 10A and Adventurer Li 30A, or browse Renogy charge controllers. For a higher-voltage array, compare the input limits of an appropriate MPPT model rather than assuming a larger PWM amp rating is enough.
Installation fit and documents
163.8 × 109.6 × 44.7 mm per manual (approximately 6.45 × 4.31 × 1.76 in); datasheet metric table differs; 0.65 lb (0.29 kg). Terminals accept up to 8 awg / 10 mm². Install in a dry, ventilated location; IP20 is not an outdoor waterproof rating. Connect the battery before the solar array as directed by the manual, then confirm the battery settings. Use the installation instructions for cable sizing, fusing and commissioning.
Download the Wanderer Li 30A user manual, Wanderer Li 30A specification sheet and Renogy limited warranty (A7). 1-year material and workmanship warranty, subject to Renogy terms.
The manual and datasheet differ slightly on metric dimensions and contain inconsistent Celsius/Fahrenheit minimum temperatures. Use the manual’s mechanical drawing for fit and confirm extreme-cold requirements with Renogy.
Plan the rest of the system
solar charge-controller sizing guide · Rover Li 30A · MPPT versus PWM guide.
| Selected Product SKU | RNG-CTRL-WND30-Li-G1-US |
|---|---|
| Manufacturer Model | RNG-CTRL-WND30-LI |
| Charging Technology | PWM (pulse-width modulation), not MPPT |
| Battery System | 12V only |
| Rated Charging Current | 30 A |
| Maximum PV Open-Circuit Voltage | 25 V DC maximum |
| PV Array Guidance | Select by 30 A charge-current and 25 V PV-voltage limits; no universal array configuration is implied |
| Battery Profiles | Sealed AGM, gel, flooded and compatible lithium; configure to battery manufacturer requirements |
| Lithium Setup | 12.8 V LFP defaults; supported monitoring interface required for parameter changes |
| Display | LED status indicators and battery-type button; no LCD |
| Dedicated DC Load Output | No dedicated DC load terminals; connect appropriately protected loads to the battery system |
| USB Output | No USB output |
| Communication | RS232; optional Renogy BT-1 Bluetooth module, sold separately |
| Enclosure Rating | IP20 |
| Dimensions | 163.8 × 109.6 × 44.7 mm per manual (approximately 6.45 × 4.31 × 1.76 in); datasheet metric table differs |
| Weight | 0.65 lb (0.29 kg) |
| Terminals | Up to 8 AWG / 10 mm² |
| Self-Consumption | ≤10 mA |
| Operating Temperature | Manual/datasheet list -35°C to +45°C, but their -20°F lower value and retail temperature figure do not convert consistently. Confirm minimum service temperature. |
| Temperature Compensation | -3 mV/°C/2V for applicable non-lithium charging profiles |
| Included Components | 1 × Renogy Wanderer Li 30A PWM Charge Controller |
| Connection Sequence | Battery first, then solar; follow exact-model installation manual |
| Warranty | 1-year material and workmanship warranty, subject to Renogy terms |
| Grounding Type | Negative ground |
| Mounting Clearance | 6 in (150 mm) above and below per manual |
| Mounting Hardware | Wall-mounting screws not supplied per manual |
| High Voltage Disconnect | 16 V per manufacturer table |
| Optional Temperature Sensor | Remote sensor; battery-profile restrictions apply |
| Selected variant SKU | RNG-CTRL-WND30-Li-G1-US |
Product reference specifications
Specifications for the selected option are shown above. These product reference details describe the listing and its available configurations.
| Manufacturer Model | RNG-CTRL-WND30-LI |
|---|---|
| Charging Technology | PWM (pulse-width modulation), not MPPT |
| Battery System | 12V only |
| Rated Charging Current | 30 A |
| Maximum PV Open-Circuit Voltage | 25 V DC maximum |
| PV Array Guidance | Select by 30 A charge-current and 25 V PV-voltage limits; no universal array configuration is implied |
| Battery Profiles | Sealed AGM, gel, flooded and compatible lithium; configure to battery manufacturer requirements |
| Lithium Setup | 12.8 V LFP defaults; supported monitoring interface required for parameter changes |
| Display | LED status indicators and battery-type button; no LCD |
| Dedicated DC Load Output | No dedicated DC load terminals; connect appropriately protected loads to the battery system |
| USB Output | No USB output |
| Communication | RS232; optional Renogy BT-1 Bluetooth module, sold separately |
| Enclosure Rating | IP20 |
| Dimensions | 163.8 × 109.6 × 44.7 mm per manual (approximately 6.45 × 4.31 × 1.76 in); datasheet metric table differs |
| Weight | 0.65 lb (0.29 kg) |
| Terminals | Up to 8 AWG / 10 mm² |
| Self-Consumption | ≤10 mA |
| Operating Temperature | Manual/datasheet list -35°C to +45°C, but their -20°F lower value and retail temperature figure do not convert consistently. Confirm minimum service temperature. |
| Temperature Compensation | -3 mV/°C/2V for applicable non-lithium charging profiles |
| Included Components | 1 × Renogy Wanderer Li 30A PWM Charge Controller |
| Connection Sequence | Battery first, then solar; follow exact-model installation manual |
| Warranty | 1-year material and workmanship warranty, subject to Renogy terms |
| Grounding Type | Negative ground |
| Mounting Clearance | 6 in (150 mm) above and below per manual |
| Mounting Hardware | Wall-mounting screws not supplied per manual |
| High Voltage Disconnect | 16 V per manufacturer table |
| Optional Temperature Sensor | Remote sensor; battery-profile restrictions apply |
Frequently Asked Questions
Clear answers to common questions about this product, setup, compatibility, and use.


